30 cheap kitchen cabinet add-ons you can DIY (2023)

These inexpensive, easy-to-build closet projects will help you utilize every nook and cranny of your kitchen storage space.

Each editorial product is independently selected, although we may receive compensation or receive an affiliate commission if you purchase something through our links. Ratings and prices are correct and items are in stock at the time of publication.

You can size this knife stand to fit anyonecloset doorand any number of knives e.gkitchen cabinetStorage. To build this rotated cutting board knife stand, all you need is a table saw and scrap wood. Run the scraps edge-on over the saw to cut kerfs. Adjust the blade height to the width of the knife blades. These cuts will require you to remove the saw's blade guard, so use extra care. Also cut a thin strip that will serve as an end cap. Glue and clip the trimmings together and grind the knife stand until the joints are flush. Use two 1-1/4-in. Screws and finished washers.

Base cabinets have the least convenient storage in your kitchen. We'll show you how to keep everything in your closet close at hand by retrofitting your base cabinets with classic rollout shelves. This tutorial shows how to construct a dedicated recycling and trash rollout without using expensive floor mounting hardware. Get step-by-step instructions on how to measure,Structure of the rollout drawerand its support, attaching the drawer slides and mounting the unit in the cabinet.

There is plenty of usable space under many top kitchen cabinets, and it's the perfect place to store your favorite wines. This easy to build wine rack only requires two 1x4s the length of the base bay and a 3/4 inch strip. plywood the same length and 8 inches wide.Click here for the full project plans for building a wine rack.

This kitchen cabinet storage project provides more space for plates and bowls in cluttered kitchen cabinets. Most closets only have one or two shelves, which wastes a lot of space. So we added one (and sometimes two) shelves to most of our closets. All it takes is 3/4-in. plywood and a bag of shelf supports. The supports come in two diameters, so bring an existing one to the store to make sure you get the right size.

If your spices are stuck in a drawer and only the tops are visible, this nifty shelf that slides neatly into the drawer will solve the problem. And it only takes an hour to set up. Do it with 1/4-inch scraps. and 1/2 inch. Plywood. OrBuild a two tier spice rackin your kitchen drawer. Even easier -Hot glue stir sticks in your spice drawerfor a cheap and easy spice organizer.

This tray is perfect for pens and paper. When closed, it is mostly hidden by the front frame of the cabinet. Hinges and magnets keep this tray under a wall cabinet. To install the tray, first screw on the hinges. Then open the cabinet door at the top and clamp the tray to the bottom of the cabinet while screwing the hinges to the cabinet. Need a more robust command center? Here ishow to build a message centerinstead in your kitchen.

The space under sinks is often overlooked, but it's the best place for rollouts.This article contains step-by-step instructionshow to build two types of customizable rollout trays that fit around and under plumbing pipes, garbage disposals, and other obstructions under your sink. These rollouts transform the “not sure what's underneath” storage space into an organized and efficient place for cleaning supplies that lets you see everything you have at a glance.

About Amazon

Unless you love opening yoursspice cabinetand dropping little bottles of cinnamon and peppers on you all the time, this is definitely one of those kitchen organization hacks you should try. ThisSpice Claw ClipsStore spices in neat rows in a cabinet or at the back of a door.

The secret of this project is "rare earth" magnets. The ones we use are only 5/32" in diameter and 1/8" in height. Browse online to find many shapes and sizes. Attach magnets to the corners of your cutting board and add more as needed. Make the metal plate under the cabinet larger than the cutting board so the board can be easily put away. Glue the sheet metal to plywood with spray adhesive. Drill holes near the corners and screw it to the bottom of a cabinet. Drill holes the size of the magnets and put a dab of superglue in them. Insert the magnets with a nail head. Slide the nail aside to release the magnet. The metal plate grips the magnets. Make sure you use galvanized steel, not aluminum. Also learnhow to make your own cutting board!

Most kitchen base cabinets lack vertical storage space for large, flat cookware like baking sheets and pizza trays. To do this, simply remove the bottom shelf, cut a vertical sheet of plywood, and secure it to the cabinet bottom with furniture braces and at the top with a wooden batten. Drill holes for the adjustment pins to match the original positions and trim the shelf to length.Watch this video to learn more kitchen cabinet storage ideas.

ToStore cutting boards, mount a rack to a closet door. Use a sheet of 1/4 inch thick acrylic plastic; Plywood would work too. You can cut acrylic with a table saw or circular saw as long as you cut slowly. Beat off the sharp edges with sandpaper. Round off the bottom corners with a belt sander. For standoffs, use #14-8 crimp barrels (found in the electrical aisles at home centers), or any type of pipe or even blocks of wood would work.

Prevent small items from getting lost in deep base cabinets. If you know how to mount a sheet of plywood onto drawer slides, you can take advantage of any of the nifty shelving, hooks, and brackets sold at home centers. It's easy as long as you remember two important things: First, make sure the drawer slides are parallel. Place a plywood spacer between the drawer units as you screw them to the panel. Screw the cabinet elements to studs. Second, make your cleats thick enough for the rails to clear the cabinet door hinges. (We glued 1/2" plywood to 3/4" plywood to make my cleats.) To install the panel in the closet, reassemble the rails. Hold the entire assembly against the cabinet wall and slide the panel out about 4 inches. Thread the screws through the lugs on the back, then slide the panel all the way out and turn the screws on the front.

Of course, the pan or tray you need is always the one at the bottom of the stack! Here's the solution: Store tall, flat items on end rather than stacked. This will allow you to pull out the pan you want. Cut 3/4-in. Plywood to match the depth of the cabinet, but make it at least an inch higher than the opening so you can attach it to the face frame as shown. Drill holes for the shelf supports to match the existing holes in the cabinet. Screw two angles to the cabinet bottom; one to the front frame and one to the back wall of the case (not shown). Finally, trim the old shelf to fit the new space. Here are moreKitchen storage projects that free up space.

What's hiding under your kitchen sink? If the space under your sink is anything like ours, it's a cluttered mess of cleaning supplies, sponges, and plastic bags. Here's a great way to store those items right by the sink cabinet door. Cut a plastic storage tub in half with a utility knife and screw it through the plastic lip at the top of the tub to the inside of the cabinet door. Just make sure you position it so you can close the closet door when all your bags and other supplies are in the bin.

Deep drawers often contain a tangled stack of interlocking utensils. Our solution is aSliding tray that creates two flatter spaces. Make it 1/8-in. Narrower than the drawer box, about half the length and any depth (ours is 1-3/4 inches deep). Don't rely on measurements and arithmetic to position the holes for the adjustable shelf supports. Instead, position the tray at least 1/8-inch into the drawer box. lower than the cabinet opening and make a mark on the tray. Our shelf supports fit tightly into the holes, but yours may need some superglue. This simple drawer rests on shelf supports.

You can mount a pot lid drawer under your pot rack – or under any other cupboard shelf. Before removing the shelf, make some pencil marks on it to indicate the width of the cabinet opening at its narrowest point (usually at the hinges). Your drawer front and slides can't protrude past these marks (or you'll spend hours building a drawer that won't open). Then remove the shelf. If it's chipboard, we recommend replacing it with 3/4-in. plywood and transfer the markings to the new shelf. If you can build a simple drawer box, the rest will be easy. Mount the drawer on cleats screwed to the body sides. Check out thesehome-friendly kitchen upgradeideas.

Here's an easy project to bring order to the chaos: a door-mounted storage rack that can be accomplished with some basic carpentry skills and a few hand tools. You can also change this basic idea to organize other closets.

Keep your tablet handy and secure. Follow the recipes online without worrying about spilling your expensive tablet. This tray keeps your tablet computer off the countertop. When it swings down, it also swings forward so the tablet doesn't get hidden under the cabinet. The mechanism is simple; just make and position the arms exactly as shown here and it will work smoothly. We cut the aluminum parts and rounded the corners with a grinder. When closed, small cupboard door magnets hold the tray. We cut the plastic ears off the magnets and glued the magnets in place with epoxy. The insert in the tray is a foam placemat cut to fit. The shelf folds against a sheet of plywood and is an option for kitchen cabinet organizers. Aluminum arms hold the tray in place. Don't worry, small magnets won't hurt your tablet; it actually contains magnets.Plus: keep your kitchen sparkling clean with these secret cleaning tips from professional household cleaners.

Designed for wood floor transitions, the T-moulding is a perfect shelf for stemware. Simply cut to length, pre-drill screw holes and screw to the underside of a shelf. Use brass screws and washers for a neater look. Precast T-shapes are available wherever hardwood floors are sold. a 4ft. Section costs about $25. Watch our funny videoMake your own wine glass storage rackfor more great kitchen storage ideas.

You can make this nifty, inexpensive shelf and mount it in a closet door to store your cutting boards out of sight. It goes together in a snap as it only requires a 6 foot. 1x2 and two L brackets. Measure between the door jambs to get the maximum width of your rack. Make sure the rack is wide enough for your cutting board (or jump for a new one). You also need to mount the rack low enough so that it doesn't hit a closet shelf when you close the door. Cut the bottom and fascia rails to match the distance between the cabinet door jambs. Cut the sides 7-1/4 inches long. Nail the sides to the base. Then nail the two face pieces at the top and bottom to complete the frame (photo left). The easiest way to assemble the rack is to unhook the cabinet door and lay it down. Pre-drill the screw holes for the L-brackets and use a 1-inch screwdriver to mount the rack to the cabinet door. L-Brackets centered on each side of the rack.

Free up space in the pantry by usinghanging measuring cups in a kitchen cupboard. Position and mount a wooden bar so that the cups hang between the shelves and the door can be closed completely. Assemble a second bar for your measuring spoons, then screw cup hooks onto both bars.

Most cabinet manufacturers now build pull-out shelves into their base cabinets. But if you don't have that convenience, this project will elevate those shelves. Here we show you how to make a complete roll out pantry. The hardware consists of two heavy-duty bottom-mounted rails and a center-mounted top slide that together can support 130 lbs. Here, too, you construct your device according to your needs. We made our bottom tray 3-1/2 inches high and the top 2-1/2 inches high. If you're storing cereal boxes and other large packaging, you may only want to fit in two trays. Since you are converting your door from pan to roll mode, you will need to remove the door and hinges. You will also need to remove the existing handle and reinstall it in the center of the door. If your hardware will be rear mounted, install it before attaching the door.Get the full guide here.

Pegboard is great fororganize kitchens, laundry rooms and bathroom cabinets. Using a rebate bit, route a groove in a 1x2 frame, attach the pegboard with glue and pins, then mount to the door. The frame supports the edges of the pegboard and creates a 1/2-in. Space behind the board to allow pens to be inserted.

Tired of slamming those closet doors? Removable bumpers for doors and drawers are theSolution for noisy kitchen cabinets. Pick up a pack of 20 at a home center for a few bucks oronline at Amazon. Make sure the back of the door is clean so the bumpers will stick, then place one on the top corner and another on the bottom.